Audio, Navigation System & Related • ACM Suddenly Working Again?
I have a 2014 SEL. Over a year ago, I had the snap, crackle pop! of the speakers happen and then no sound. Read up on this forum, checked fuses, narrowed it down and figured it must be a bad ACM....
View ArticlePowertrain / Under The Hood • Re: Multiple turbo failures
I experienced the same issue. My problems started after a water pump failure and a recommendation to replace the timing. Essentially the valve cover had to be replaced and a bolt was stripped. After...
View ArticleAudio, Navigation System & Related • Re: ACM Suddenly Working Again?
Thats great. I am guessing that might not be the last of it though. I do hope I am wrong.
View ArticleTechnical / How-To Articles • loose wheel bearing assembly
It's a 2018 SEL FWD with the 3.5L V6 (normally aspirated). There's been some "mud tire noise" for a while. Rotating tires did nothing, so I moved on to wheel bearings. As is the case with everyone...
View ArticleTechnical / How-To Articles • Re: loose wheel bearing assembly
Mine fit in nice and snug. No wiggle room. I noticed the new OEM bearings also have 2 rubber seals around them to keep water out and reduce corrosion. The knuckles are aluminum.
View ArticleClassifieds • titanium Tail lights
Titanium Tail lights. Excellent condition. Sold my Flex Will ship at purchaser expense. 425.00 + shipping
View ArticleClassifieds • Illuminated Door Sill
Used Illuminated Flex door sill plate. In good condition. Sold my Flex.35.00 plus shipping.
View ArticleClassifieds • K & N Performance intake system
Used K& N intake system off a 2018 limited. Good condition 249.00 plus shipping.
View ArticlePowertrain / Under The Hood • Trouble finding "D" Drive gear
Hello all!Just acquired a 2016 Ford Flex SEL AWD, 130k miles, after finally letting go of my 2009 with 270k miles. The only issue I have found with the car in the past few days since owning it, is...
View ArticlePowertrain / Under The Hood • Sudden loss of cabin heat at idle
2015 Flex Limited (Ecoboost) / 140,000 miles-Coolant was last flushed and replaced 2012 / 80,000 miles-temperature reads 'normal' on the dash-coolant level in expansion tank is good and has not...
View ArticlePowertrain / Under The Hood • Re: Sudden loss of cabin heat at idle
After my previous post, I continue to look online and see that others have had similar problems. Specifically, I located TSB 12 – 4–2.The TSB seems to specify 2009 to 2012, but I called my dealer to...
View ArticleClassifieds • Re: Illuminated Door Sill
That's a good deal. I love my illuminated sills.They're nearly impossible to find nowadays.
View ArticleInterior • Blower motor or something else?
I have a 2009 Flex Limited, and a couple weeks ago I started only getting cold air on the passenger side. Based on the many posts on this site, I figured it was the blend door actuator. I replaced the...
View ArticlePowertrain / Under The Hood • Re: Trouble finding "D" Drive gear
See your Redit thread.https://www.reddit.com/r/FordFlex/comme ... into_gear/
View ArticleWelcome / Introductions • Re: Who has the highest mileage and still driving...
I also have a 2009 Flex Limited with 178,124 miles. I would like to see it get to 250K if possible. It has been a wonderful vehicle!
View ArticleClassifieds • Husky rear bed liner
Used HUSKY rubber rear bed liner. In good condition. 65.00. Bulky item to ship but will if U are willing to pay.thanksFred
View ArticleWelcome / Introductions • 2014 fuel level issuse
I have a 2014 SEL 3.5. My fuel level will go from full to 1/2 tank and then start to increase again, as if I added fuel. Any recommendations before I replace the fuel sending unit ?Hopefully I have...
View ArticleGeneral Ford Flex Discussions • Rear control arm bushing bolt spinning
I was supposed to replace the rear control arm on my Flex but one bolt was impossible to remove (see in the picture). The bolt is spinning on place and do not go down. I even pressed down with a...
View ArticleGeneral Ford Flex Discussions • Re: Rear control arm bushing bolt spinning
Put a pry bar, screwdriver or needle nose pliers in there between the bolt and the arm and try to loosen it when there is pressure pushing the bolt out.I see you tried the prybar but did you do it...
View Article